HRP Australia
Gas Well Deliquification

Keep liquid-loaded gas wells flowing.

As reservoir pressure falls, liquids build up in the well and choke gas production. An HRP rod pump removes them steadily, even at very low rates, so the well keeps producing gas.

0.05Minimum SPM
99%Uptime on a QLD deep gas well
6,791 ftPump set depth
0Lift gas needed
The Challenge

Liquid loading stalls gas wells.

Liquids build up

Declining reservoir pressure means the gas can no longer carry liquids to surface. Rates fall, flow becomes unstable, and the well can stop altogether.

Low rates are hard to lift

Liquid volumes are often small. Many lift methods lose efficiency at low rates, and conventional pumping units are limited to around 1 SPM.

Gas gets in the pump

Free gas reduces pump fill and can gas-lock a conventional rod pump, cutting efficiency and causing failures.

How HRP Helps

Built for low rates, gas and long runs.

Ultra-low SPM, no start-stop

SPM goes as low as 0.05 without the conventional 1-SPM limit, so the unit runs continuously instead of cycling on and off.

Constant stroke velocity

SPM is set by the dwell time between strokes, so each stroke keeps its velocity at low rates and solids stay suspended.

Better gas handling

The long stroke gives a higher compression ratio. Operators have seen gas produced through the pump while pump efficiency stays strong.

Gas-handling downhole pumps

Specialty pumps for high gas-liquid ratios and solids, including designs that break gas lock.

Pump-off control

Automatic pump-off control, fluid level monitoring and dynocards keep the pump matched to what the well delivers.

No lift gas, low power

No compressors or fuel gas, and a low-energy power unit driven by an electric motor, an engine or a genset.

Results

Proven on Queensland gas wells.

From a deep gas well unloading 15–20 BPD to a horizontal CSG well drawn down to pumped-off conditions.

HRP unit at the ADZ Energy Pty Ltd well site
In operation since 2020, the HRP has provided reliable, low-maintenance operation, proving itself as a robust and trusted solution for our well operations.
99%Uptime
6,791 ftPump set depth
5+ yrsSince Dec 2020, no major servicing
Read the full testimonial

Installed on ADZ's deep gas well (MC3) since December 2020, the unit has run steadily at 0.5–1 SPM, unloading 15–20 BPD of liquids with 99% uptime.

To date no major servicing has been required — no hydraulic pump replacement, valve change, hose replacement or cylinder change — and operator visits have been minimal, with long intervals between.

"The team at HRP has been very supportive to our operations throughout the years and are always available when needed, both onsite and in our offices."

WR
Wayne RichardsGM – Upstream Projects, ADZ Energy Pty Ltd
HRP unit at the Denison Gas well site
The HRP system demonstrated excellent reliability, low maintenance requirements, and strong performance in a high-deviation CSG application, supporting stable production across a wide turndown range.
~80°Horizontal CSG well
13 moContinuous, no downhole failures
0Downhole & surface issues
Read the full testimonial

Installed on a Yellowbank pilot well — a horizontal coal seam gas well (~80° deviation, DLS up to 10.37°/100 ft) — for dewatering. Online July 2023, it ran continuously for ~13 months; the well was shut in only because the pilot concluded, not due to any equipment limitation.

Rod pump set at 3,258 ft MD (2,415 ft TVD) in 3-1/2" tubing, driven by a 240" stroke HRP with an H100 Genesis power unit. Production rose from ~50 BPD to 130 BPD and was drawn down to pumped-off conditions at ~25 BPD.

The reduced downstroke velocity improved rod fall and significantly minimised rod compression, buckling and side loading. Gas was produced through the pump while maintaining strong pump efficiency, attributed to the higher compression ratio of the long stroke.

The fully enclosed stuffing box performed as designed with zero wellbore fluid leaks, and the HPU needed only routine filter changes and hydraulic oil top-ups.

CH
Chris HolmesVP Exploration & Development, Denison Gas
HRP installation, Surat Basin QLD (Gas well)

Surat Basin

Gas
Stroke
Production
240"
30 BPD
Pump depth
Region
2,075 m
QLD
Installed Jun 2020
Comparison

HRP versus gas lift and ESP for liquid-loaded wells.

FactorHRP rod pumpGas liftESP
Late-life / low rateStable at ultra-low SPMWeak; liquid loadingUnstable at low intake
DrawdownVery high; pumps near-dryLimitedLimited by cavitation / gas lock
Gas handlingGas-handling pumps availableNative advantageSensitive; gas lock risk
Gas dependencyNoneCriticalNone
Power / infrastructureLow energy, minimalCompressors + fuel gasHigh electrical demand
TurndownWide (SPM, stroke)LimitedLimited
FAQs

Deliquification questions.

How low can the pumping rate go?

Down to 0.05 SPM. Because SPM is set by dwell time between strokes, stroke velocity stays constant, and the unit runs continuously rather than cycling on and off.

Will gas interfere with the pump?

The long stroke gives a higher compression ratio, which helps the pump handle gas. Specialty gas-handling downhole pumps are also available for high gas-liquid ratios.

How much maintenance does it need?

ADZ Energy reports 99% uptime on a deep gas well in operation since 2020, with no major servicing and minimal operator visits.

Does it need lift gas or high power?

No. There are no compressors or fuel gas, and the power unit is low-energy, driven by an electric motor, an engine or a genset.

Have liquid-loaded gas wells?

Share your well data and we'll come back with a deliquification design.

Contact HRP Australia