HRP Australia
Hydraulic Rod Pumps Australia

Unlocking the full potential of rod pumping.

Ultra long stroke slimline hydraulic rod pumping unit. Experience the next generation of rod pumping and what it can do for your well production.

336"Maximum stroke length
~4 hrsInstall & commission
0.05Minimum SPM
1987Proven since
About HRP

Ultra-reliable, low-profile rod pumping — proven since 1987.

Hydraulic Rod Pumps International (HRPI) was established in 1987 in Los Angeles, California, to answer the oil and gas industry's call for pumping units that are ultra-reliable, low profile, low maintenance and suited to highly sensitive areas.

Reliability and minimum impact on the environment were key reasons producers adopted the technology. Today HRP is installed in some of the world's most challenging applications — and HRP developed the world's first and only below-ground hydraulic pumping unit.

HRP Australia Pty Ltd, based in Mansfield, Queensland, brings this technology to Australian operators with local engineering, spares, ready-to-deploy units and field support.

600+Producing wells in the USA
12 yrsCylinder run life recorded
100%Fully Australian spec'd & certified
QLDLocal spares & ready-to-deploy units
Enclosed HRP installation in a landscaped Los Angeles neighbourhood
HRP units operate in Los Angeles neighbourhoods beside schools, studios, high-rises and parks.
Built for scrutiny. Operating under extreme scrutiny on reliability and operability, HRP lets producers keep producing in the most sensitive locations.
How It Works

A hydraulic cylinder, a power unit and a smart controller.

A plug-and-play package: the hydraulic cylinder bolts directly onto the composite rod lock and is powered by a hydraulic power unit (HPU) via hydraulic hoses.

Hydraulic cylinder with internal piston and integral polished rod, powered by the HPU via hydraulic hoses.
Prime mover — electric motor (or gas/diesel engine) drives a hydraulic pump that provides fluid power to the system.
Hydraulic valving system controls the flow of oil to the cylinder and back to the HPU, via cooler and filter.
PLC pump controller and motor control panel run the system, with local and wireless control.
The complete HRP package: GENESIS power unit, hydraulic hoses, cylinder and wellhead. Explore it in 3D →

Upstroke

  • Hydraulic pump draws oil from the reservoir
  • Oil is pumped to the directional valve stack
  • Valve stack directs flow to the cylinder, lifting the inbuilt piston
  • The piston's integrated polished rod lifts the rod string

Downstroke

  • Gravity pulls the rod string down
  • The piston moves down, pushing oil out of the cylinder
  • Oil returns via the valve stack, cooler and filter to the reservoir
  • Piston rests at the bottom awaiting the next upstroke

Lifting force

Pressure is applied only to the rod end (bottom of the piston), retracting the rod upward. No pressure is applied to the blind end — gravity extends the rod.

Effective area = Piston area − Rod area
Lifting force = Hydraulic pressure × Effective area

SPM changes by dwell time — not stroke speed.

Unlike a beam unit, LRP or tower unit, HRP changes SPM by adjusting the dwell time between complete strokes. Every up and down stroke keeps the velocity set by the operator.

On conventional units, slowing SPM slows the plunger — affecting rod harmonics, rod stretch, plunger slippage and, critically, solids. As plunger velocity drops, particles that were held in suspension fall and settle in the pump, risking downhole pump failure.

With HRP, the plunger moves at the same velocity at low SPM as at high SPM, keeping solids suspended and produced out of the pump.

Stroke velocity vs SPM

Plunger velocity SPM → solids settle HRP — constant Conventional unit

Integral double seals — field serviceable

  • No leak to the external environment
  • Auto-lubrication
  • Upper seals contain hydraulic fluid; lower seals (within floating piston) contain wellbore fluid
  • Middle chamber collects fluid and ports it to external containment

Designed for in-situ service

  • Sliding-sleeve design lets lower seals be changed with the cylinder in place
  • Floating piston for pressure balance adjustment
  • Drain port for external containment
  • Leak detection device attachment available
Pump Controller

Full visibility of every stroke.

Built-in CPU and HMI with local and wireless access, automatic pump-off control, fluid level monitoring and dynocards.

Operator control

  • Change SPM
  • POC (Pumped-Off Controller) settings

Operator monitoring

  • Dynocards
  • Trends: SPM, oil level & temp, amps & volts, polished rod load, pump fill

Operator settings & alarms

  • Oil level and temperature min/max
  • Filter max pressure alarm
  • Max system and max upstroke pressure
The HRP controller HMI running live: dynocard, pressure and piston position, SPM control mode, stroke timing, wellhead pressures and fluid level.
Specifications

Application envelope & system specifications.

A modular design: cylinders and downhole equipment can stay in the well long-term, while the HPU specification can be changed after commissioning to suit a wide range of production rates.

15,000 ftDepth up to
2,500 BPDProduction up to
53,376 lbsPolished load up to
336 inStroke length up to
0.05–3.5SPM range
ParameterSpecification
Actuation typeHydraulic cylinder
DriverHydraulic power unit — electric motor or engine (gas, diesel)
Stroke lengths60", 86", 120", 240", 336"
Hydraulic cylinder sizes2.50", 3.00", 3.50", 4.00", 4.50", 5.00"
PPRL range11,000 – 53,600 lbs
Power unit ratings5 – 150 kW
Pump controllerBuilt-in CPU & HMI, local and wireless, SPM change, automatic POC, fluid level monitoring, dynocards
Stuffing boxIntegrated seals
Comparison

How HRP compares with beam, tower and LRP units.

HRP is an alternative to beam units, ESPs, PCPs and gas lift — combining the reliability of a long-stroke rod pump with a minimal wellhead footprint.

FeatureHRPBeam / Tower / LRP
Civil worksNone requiredFoundations typically required
Install time~4 hoursDays, incl. civil contractors
Low-SPM behaviourConstant stroke velocity (dwell)Velocity falls with SPM
Minimum SPMAs low as 0.05Typically ~1 SPM limit
ProfileLow; below-ground optionTall / large structure
Maintenance accessGround levelOften at height
Stuffing boxFully sealed, integratedConventional packing
Changing capacitySwap HPU; cylinder staysReplace or re-gear unit
240-inch HRP cylinder beside a tower pumping unit
A 240" HRP cylinder beside a 236" tower unit — similar stroke, a fraction of the footprint.
Installations

Proven in Queensland's CSG, oil and gas fields.

From shallow CSG wells to 2,000 m+ gas wells and highly deviated wellbores, HRP is producing across Queensland's major basins.

HRP installation, Galilee Basin QLD (CSG well)

Galilee Basin

CSG
Stroke
Production
336"
1,100 BPD
Pump depth
Region
1,000 m
QLD
Installed Dec 2020
HRP installation, Surat Basin QLD (CSG well)

Surat Basin

CSG
Stroke
Production
240"
300 BPD
Pump depth
Region
710 m
QLD
Installed May 2021
HRP installation, Surat Basin QLD (CSG well)

Surat Basin

CSG
Stroke
Production
240"
200 BPD
Well
Region
78° deviated
QLD
Installed Jul 2023
HRP installation, Moranbah QLD (CSG well)

Moranbah

CSG
Stroke
Production
240"
250 BPD
Pump depth
Region
679 m
QLD
Installed Nov 2022
HRP installation, Bowen Basin QLD (CSG well)

Bowen Basin

CSG
Stroke
Production
240"
95 BPD
Pump depth
Region
907 m
QLD
Installed Jun 2024
HRP installation, Cooper Basin QLD (Oil well)

Cooper Basin

Oil
Stroke
Production
240"
300 BPD
Pump depth
Region
1,540 m
QLD
Installed Jun 2020
HRP installation, Surat Basin QLD (Oil well)

Surat Basin

Oil
Stroke
Production
240"
110 BPD
Pump depth
Region
1,000 m
QLD
Installed Dec 2020
HRP installation, Surat Basin QLD (Gas well)

Surat Basin

Gas
Stroke
Production
240"
30 BPD
Pump depth
Region
2,075 m
QLD
Installed Jun 2020
USA Heritage

Producing in the heart of Los Angeles.

36+Years operating history
600+Producing wells
12 yrsCylinder run

Onshore and offshore, HRP units operate beside schools, movie studios, high-rise towers and parks, under extreme scrutiny of their reliability and operability.

HRP installations in Los Angeles
Testimonials

What Australian operators say.

Operators running HRP units in Queensland's CSG and deep gas wells share their results in their own words.

HRP unit at the Denison Gas well site
The HRP system demonstrated excellent reliability, low maintenance requirements, and strong performance in a high-deviation CSG application, supporting stable production across a wide turndown range.
~80°Horizontal CSG well
13 moContinuous, no downhole failures
0Downhole & surface issues
Read the full testimonial

Installed on a Yellowbank pilot well — a horizontal coal seam gas well (~80° deviation, DLS up to 10.37°/100 ft) — for dewatering. Online July 2023, it ran continuously for ~13 months; the well was shut in only because the pilot concluded, not due to any equipment limitation.

Rod pump set at 3,258 ft MD (2,415 ft TVD) in 3-1/2" tubing, driven by a 240" stroke HRP with an H100 Genesis power unit. Production rose from ~50 BPD to 130 BPD and was drawn down to pumped-off conditions at ~25 BPD.

The reduced downstroke velocity improved rod fall and significantly minimised rod compression, buckling and side loading. Gas was produced through the pump while maintaining strong pump efficiency, attributed to the higher compression ratio of the long stroke.

The fully enclosed stuffing box performed as designed with zero wellbore fluid leaks, and the HPU needed only routine filter changes and hydraulic oil top-ups.

CH
Chris HolmesVP Exploration & Development, Denison Gas
HRP unit at the ADZ Energy Pty Ltd well site
In operation since 2020, the HRP has provided reliable, low-maintenance operation, proving itself as a robust and trusted solution for our well operations.
99%Uptime
6,791 ftPump set depth
5+ yrsSince Dec 2020, no major servicing
Read the full testimonial

Installed on ADZ's deep gas well (MC3) since December 2020, the unit has run steadily at 0.5–1 SPM, unloading 15–20 BPD of liquids with 99% uptime.

To date no major servicing has been required — no hydraulic pump replacement, valve change, hose replacement or cylinder change — and operator visits have been minimal, with long intervals between.

"The team at HRP has been very supportive to our operations throughout the years and are always available when needed, both onsite and in our offices."

WR
Wayne RichardsGM – Upstream Projects, ADZ Energy Pty Ltd
Service & Support

Local support from selection to teardown analysis.

Pre-sales support

  • Application engineering — selection and design of HRP and associated tie-in equipment.
  • Training — selection, installation, commissioning, operation, maintenance, troubleshooting, safety and compliance, in the classroom and on site.
  • Documentation — datasheets, manuals and SOPs.

Post-sales support

  • On-site installation and commissioning support.
  • Ongoing operation, maintenance and troubleshooting support.
  • Local spares with quick deployment.
  • Ready-to-deploy cylinders and HPUs held locally.
  • Refurbishment and teardown analysis capabilities.

Our commitment

We are committed to being partners in rod-pumping surface driver technology.

Partnership

Our customers' success is our success.

Transparency

Open communication on deliverables.

Continual improvement

Constantly finding new ways to deliver benefits.

Listen & understand

Your feedback shapes our products, processes and services.

FAQs

Frequently asked questions.

What wells is HRP best suited to?

HRP is ideal for wells with variable production rates, liquid-loaded and troublesome wells, deep or deviated wells, CSG wells, and any well where a traditional rod pump would be considered — particularly where footprint, visual impact or civil works are a concern.

Can HRP be used on offshore platforms?

Yes. The all-in-one HPU has a 1.7 m × 1.7 m footprint, lifts with a ~5 T platform crane, can drive two wells, and can run on a genset. Paired with a rod-retrievable insert pump, it installs without a tubing pull or rig workover, which makes it well suited to marginal and late-life offshore wells.

How quickly can a well be converted from PCP to SRP?

Installation and commissioning are typically completed within about 4 hours, with no civil works — enabling much faster well reactivation.

How low can the SPM go?

The SPM range is 0.05 to 3.5. Because SPM is set by dwell time between strokes, stroke velocity stays constant even at very low rates, so the unit can run continuously without start-stop cycling.

Can I change capacity after installation?

Yes. The modular design lets the cylinder and downhole equipment remain in the well while the HPU specification is changed to suit different production rates.

What drivers are available for the power unit?

Electric motors, or gas or diesel engines, with power ratings from 5 to 150 kW.

Do you hold spares and units in Australia?

Yes. HRP Australia holds spares and ready-to-deploy cylinders and HPUs locally, and offers refurbishment and teardown analysis.

Contact

Let's talk about your wells.

Tell us about your field and production goals and our application engineers will be in touch.

HRP Australia Pty Ltd

Address10 Devlan Street
Mansfield QLD 4122, Australia
Globalhrpi.com

Submitting opens your email app with the enquiry addressed to sales@hrpaustralia.com.